Datasheet Texas Instruments TPS61016DGS — 数据表
| 制造商 | Texas Instruments |
| 系列 | TPS61016 |
| 零件号 | TPS61016DGS |
具有固定3.3V输出的低输入电压同步升压转换器10-VSSOP -40至85
数据表
TPS6101x High-Efficiency, 1-Cell and 2-Cell Boost Converters datasheet
PDF, 1.1 Mb, 修订版: F, 档案已发布: Aug 4, 2015
从文件中提取
价格
状态
| Lifecycle Status | Active (Recommended for new designs) |
| Manufacture's Sample Availability | Yes |
打包
| Pin | 10 |
| Package Type | DGS |
| Industry STD Term | VSSOP |
| JEDEC Code | S-PDSO-G |
| Package QTY | 80 |
| Carrier | TUBE |
| Device Marking | AIV |
| Width (mm) | 3 |
| Length (mm) | 3 |
| Thickness (mm) | 1.02 |
| Pitch (mm) | .5 |
| Max Height (mm) | 1.07 |
| Mechanical Data | 下载 |
参数化
| Duty Cycle(Max) | 100 % |
| Iq(Typ) | 0.05 mA |
| Operating Temperature Range | -40 to 85 C |
| Package Group | VSSOP |
| Rating | Catalog |
| Regulated Outputs | 1 |
| Special Features | Enable,Light Load Efficiency,Output Discharge,Power Good |
| Switch Current Limit(Min) | 1.07 A |
| Switch Current Limit(Typ) | 1.13 A |
| Switching Frequency(Max) | 780 kHz |
| Switching Frequency(Min) | 420 kHz |
| Type | Converter |
| Vin(Max) | 3.3 V |
| Vin(Min) | 0.8 V |
| Vout(Max) | 3.3 V |
| Vout(Min) | 3.3 V |
生态计划
| RoHS | Compliant |
设计套件和评估模块
- Evaluation Modules & Boards: TPS61016EVM-157
Fixed 3.3-V High-Efficiency Boost Converter
Lifecycle Status: Active (Recommended for new designs) - Evaluation Modules & Boards: TPS61015EVM-157
Fixed 3.0-V High-Efficiency Boost Converter
Lifecycle Status: Active (Recommended for new designs)
应用须知
- Modifying the PFM Operation of TPS61016 by Adding 1M Resistor at COMP PinPDF, 311 Kb, 档案已发布: Nov 29, 2004
This application report presents a way to modify the PFM mode of operation of the TPS61016 boost converter to meet low ripple voltage requirements at light load by changing the transconductance amplifier output compensation with detailed explanation and test results. - Factors That Determine Light Load PSM Switching Frequncy for TPS6101X Boost ConvPDF, 183 Kb, 档案已发布: Dec 6, 2006
This application report explains the factors that determine the low output power switching frequencies when using the TPS6101x step-up converters. - Minimizing Ringing at the Switch Node of a Boost ConverterPDF, 201 Kb, 档案已发布: Sep 15, 2006
The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter. - Basic Calculation of a Boost Converter's Power Stage (Rev. C)PDF, 186 Kb, 修订版: C, 档案已发布: Jan 8, 2014
This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed. - Extending the Soft Start Time Without a Soft Start Pin (Rev. B)PDF, 387 Kb, 修订版: B, 档案已发布: Jun 15, 2017
- Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain OutputsPDF, 130 Kb, 档案已发布: Sep 19, 2011
- IQ: What it is what it isn’t and how to use itPDF, 198 Kb, 档案已发布: Jun 17, 2011
- Performing Accurate PFM Mode Efficiency Measurements (Rev. A)PDF, 418 Kb, 修订版: A, 档案已发布: Dec 11, 2018
When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.
模型线
系列: TPS61016 (4)
- TPS61016DGS TPS61016DGSG4 TPS61016DGSR TPS61016DGSRG4
制造商分类
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)