Datasheet Texas Instruments HPA01143PWPR — 数据表

制造商Texas Instruments
系列TPS61032
零件号HPA01143PWPR
Datasheet Texas Instruments HPA01143PWPR

在TSSOP-16 16-HTSSOP -40至85中具有20uA Iq的5V输出,1A,96%高效升压转换器

数据表

TPS6103x 96% Efficient Synchronous Boost Converter With 4A Switch datasheet
PDF, 1.4 Mb, 修订版: G, 档案已发布: Mar 10, 2015
从文件中提取

价格

状态

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

打包

Pin16
Package TypePWP
Industry STD TermHTSSOP
JEDEC CodeR-PDSO-G
Package QTY2000
CarrierLARGE T&R
Device MarkingPS61032
Width (mm)4.4
Length (mm)5
Thickness (mm)1
Pitch (mm).65
Max Height (mm)1.2
Mechanical Data下载

参数化

Duty Cycle(Max)100 %
Iq(Typ)0.02 mA
Operating Temperature Range-40 to 85 C
Package GroupHTSSOP
RatingCatalog
Regulated Outputs1
Special FeaturesEnable,Frequency Synchronization,Light Load Efficiency,Load Disconnect,Power Good
Switch Current Limit(Min)3.6 A
Switch Current Limit(Typ)4 A
Switching Frequency(Max)700 kHz
Switching Frequency(Min)500 kHz
TypeConverter
Vin(Max)5.5 V
Vin(Min)1.8 V
Vout(Max)5 V
Vout(Min)5 V

生态计划

RoHSCompliant

设计套件和评估模块

  • Evaluation Modules & Boards: TPS61032EVM-208
    TPS61032 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: TPS61030EVM-029
    TPS61030 Evaluation Module (QFN Package)
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: TPS61030EVM-208
    TPS61030 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: TPS61031EVM-208
    TPS61031 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

应用须知

  • Five Steps to a Good PCB Layout of the Boost Converter
    PDF, 701 Kb, 档案已发布: May 3, 2016
  • Minimizing Ringing at the Switch Node of a Boost Converter
    PDF, 201 Kb, 档案已发布: Sep 15, 2006
    The application report explains how to use proper board layout and/or a snubber to reduce high-frequency ringing at the switch node of a boost converter.
  • Basic Calculation of a Boost Converter's Power Stage (Rev. C)
    PDF, 186 Kb, 修订版: C, 档案已发布: Jan 8, 2014
    This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed.
  • Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. A)
    PDF, 1.1 Mb, 修订版: A, 档案已发布: May 11, 2015
  • PowerPAD Thermally Enhanced Package (Rev. H)
    PDF, 983 Kb, 修订版: H, 档案已发布: Jul 6, 2018
  • Extending the Soft Start Time Without a Soft Start Pin (Rev. B)
    PDF, 387 Kb, 修订版: B, 档案已发布: Jun 15, 2017
  • Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain Outputs
    PDF, 130 Kb, 档案已发布: Sep 19, 2011
  • QFN and SON PCB Attachment (Rev. B)
    PDF, 821 Kb, 修订版: B, 档案已发布: Aug 24, 2018
  • IQ: What it is what it isn’t and how to use it
    PDF, 198 Kb, 档案已发布: Jun 17, 2011
  • Performing Accurate PFM Mode Efficiency Measurements (Rev. A)
    PDF, 418 Kb, 修订版: A, 档案已发布: Dec 11, 2018
    When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.

模型线

制造商分类

  • Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Converter (Integrated Switch)