Datasheet Texas Instruments THS5661AIPWR — 数据表

制造商Texas Instruments
系列THS5661A
零件号THS5661AIPWR
Datasheet Texas Instruments THS5661AIPWR

12位125MSPS数模转换器(DAC)28-TSSOP -40至85

数据表

12-Bit, 125 MSPS, CommsDAC Digital-to-Analog Converter datasheet
PDF, 960 Kb, 修订版: B, 档案已发布: Sep 25, 2002
从文件中提取

价格

状态

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

打包

Pin28
Package TypePW
Industry STD TermTSSOP
JEDEC CodeR-PDSO-G
Package QTY2000
CarrierLARGE T&R
Device MarkingTJ5661AI
Width (mm)4.4
Length (mm)9.7
Thickness (mm)1
Pitch (mm).65
Max Height (mm)1.2
Mechanical Data下载

参数化

ArchitectureCurrent Source
DAC Channels1
InterfaceParallel CMOS
Interpolation1x
Operating Temperature Range-40 to 85 C
Package GroupTSSOP
Package Size: mm2:W x L28TSSOP: 62 mm2: 6.4 x 9.7(TSSOP) PKG
Power Consumption(Typ)175 mW
RatingCatalog
Resolution12 Bits
SFDR59 dB
Sample / Update Rate125 MSPS

生态计划

RoHSCompliant

设计套件和评估模块

  • Evaluation Modules & Boards: THS5661EVM
    THS5661A 12-Bit, 125-MSPS Digital-to-Analog Converter Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: TSW2200EVM
    TSW2200 Low-Cost Portable Power Supply Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

应用须知

  • Using TI FIFOs to Interface High-Speed Data Converters With TI TMS320 DSPs
    PDF, 249 Kb, 档案已发布: Jun 8, 2001
    Most high-speed data converters cannot be connected directly to a digital signal processor (DSP). The required transfer rates would tie up most of the DSP's I/O bandwidth. A FIFO is an appropriate solution for this problem because it can buffer a large block of data, and the DSP can read data from the FIFO in a burst mode. This is much more efficient compared to single reads for every sampled valu
  • Wideband Complementary Current Output DAC Single-Ended Interface
    PDF, 597 Kb, 档案已发布: Jun 21, 2005
    High-speed digital-to-analog converters (DACs) most often use a transformer-coupled output stage. In applications where this configuration is not practical, a single op ampdifferential to single-ended stage has often been used. This application note steps through the exact design equations required to achieve gain matching from each output as well as a matched input impedance to each of the DA
  • Noise Analysis for High Speed Op Amps (Rev. A)
    PDF, 256 Kb, 修订版: A, 档案已发布: Jan 17, 2005
    As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu

模型线

系列: THS5661A (3)

制造商分类

  • Semiconductors > Data Converters > Digital-to-Analog Converters (DACs) > High Speed DACs (>10MSPS)