Datasheet Texas Instruments THS4121IDGN — 数据表

制造商Texas Instruments
系列THS4121
零件号THS4121IDGN
Datasheet Texas Instruments THS4121IDGN

3.3 V,100 MHz,43 V / us,全差分CMOS放大器8-MSOP-PowerPAD -40至85

数据表

THS4120, THS4121: High-Speed Fully Differential-I/O Amplifier datasheet
PDF, 1.1 Mb, 修订版: D, 档案已发布: Oct 13, 2004
从文件中提取

价格

状态

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

打包

Pin8
Package TypeDGN
Industry STD TermHVSSOP
JEDEC CodeS-PDSO-G
Package QTY80
CarrierTUBE
Device MarkingASC
Width (mm)3
Length (mm)3
Thickness (mm)1.02
Pitch (mm).65
Max Height (mm)1.1
Mechanical Data下载

参数化

2nd Harmonic79 dBc
3rd Harmonic93 dBc
@ MHz1
Acl, min spec gain1 V/V
Additional FeaturesN/A
ArchitectureCMOS,Fully Differential,Voltage FB
BW @ Acl100 MHz
CMRR(Min)64 dB
CMRR(Typ)96 dB
GBW(Typ)100 MHz
Input Bias Current(Max)1.2 pA
Iq per channel(Max)13.5 mA
Iq per channel(Typ)11 mA
Number of Channels1
Offset Drift(Typ)25 uV/C
Operating Temperature Range-40 to 85,0 to 70 C
Output Current(Typ)25 mA
Package GroupMSOP-PowerPAD
Package Size: mm2:W x L8MSOP-PowerPAD: 15 mm2: 4.9 x 3(MSOP-PowerPAD) PKG
Rail-to-RailIn to V+,Out
RatingCatalog
Slew Rate(Typ)55 V/us
Total Supply Voltage(Max)3.5 +5V=5, +/-5V=10
Total Supply Voltage(Min)3 +5V=5, +/-5V=10
Vn at 1kHz(Typ)16 nV/rtHz
Vn at Flatband(Typ)5.4 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)8 mV

生态计划

RoHSCompliant

设计套件和评估模块

  • Evaluation Modules & Boards: THS4140EVM
    THS4140EVM Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

应用须知

  • Fully-Differential Amplifiers (Rev. E)
    PDF, 867 Kb, 修订版: E, 档案已发布: Sep 19, 2016
    Differential signaling has been commonly used in audio, data transmission, and telephone systems for many years because of its inherent resistance to external noise sources. Today, differential signaling is becoming popular in high-speed data acquisition, where the ADC’s inputs are differential and a differential amplifier is needed to properly drive them.Two other advantages of di
  • High-Voltage Signal Conditioning for Differential ADCs
    PDF, 125 Kb, 档案已发布: Jun 14, 2004
    Analog designers are frequently required to convert high-voltage signals to levels acceptable to low-voltage data converters with differential inputs. This paper describes solutions for this common task using modern amplifiers and typical power supplies. Three examples of conditioning В±10V bipolar signals for low-voltage analog-to-digital converters (ADCs) are shown: a single-supply design,
  • Noise Analysis for High Speed Op Amps (Rev. A)
    PDF, 256 Kb, 修订版: A, 档案已发布: Jan 17, 2005
    As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu

模型线

制造商分类

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)